I would very much like to see this tool make a comeback!
Type: Posts; User: n0yox; Keyword(s):
I would very much like to see this tool make a comeback!
Will we have support for the PIC16F18446 soon?
This fixed my problem. I did not notice I had ticked 16fl1847 not 16f1847 in MeConfig . I changed "OSCCON = %11100000" to "OSCCON = %01110000" and added "DEFINE OSC 8". I am glad I figured it out...
I am trying to use a 16f1847 and can not get it to blink an led I am sure this is a config problem but just can't make it work. this is my config and blink program below.
Thanks!
...
I got it fixed it was a hardware issue. Thank you!
Can anyone tell me what I am doing wrong? This code just returns " 0 0 " with 3 volts on gpio.0
DEFINE ADC_BITS 10
DEFINE ADC_CLOCK 3
DEFINE ADC_SAMPLEUS 50
CMCON = 7
ANSEL = %00000001...
Sorry I got it because it was a 10mhz oscillator I needed to use "cfg = _HS_OSC" I found the answer in this pdf.
http://ww1.microchip.com/downloads/en/AppNotes/00849a.pdf
I am having problems using an external oscillator on a 16f648a. I can use the internal oscillator with no problem however when I try to use an external ceramic oscillator the code does not run. On...
I just found my problem. It was these two lines
SYMBOL RTOUT = GPIO.4
SYMBOL PEIZO = GPIO.5
I had changed my board on the last run and forgot to change the pin numbers in the code. The...
I have read this thread several times and looked at the datasheet several time as well. I am having problems with code that has worked fine in the past and suddenly I can not make GPIO.0 and GPIO.3...
So this means all of the wpu are turned off on portb if any pin is a output on portb? I guess I thought because the data sheet said "The weak pull-up is" not "The weak pull-ups are turned off it...
What I was attempting to say with that comment was that by using TRISB = %00001111 after the line containing INTCON2.7 = 0 you would set the bottom 4 bits to outputs causing those 4 bits to no...
Is this close?
INTCON2 = %00000000 ' makes all of portb have WPU ? INTCON2<7> 'page 116
TRISB = %00001111 'B. 0:3 are now outputs WPU is now off?
Thank you, I will make an order on Monday. I should have asked before I started this project.
I have tried to use the pic comparison page with some luck...
I was not aware of the 18F25K22. I should have asked for advice before I made the change. Sometimes selecting a new device can be very confusing. I will look at the data sheet for the 18F25K22 , do...
Thank you for your reply. You are right I am trying to use the internal oscillator and have no idea how to setup the oscillator section. I do not plan to use any of the special features “usb ” of...
No blinky what am I doing wrong? The below config come from meconfig.exe.
;----[18F2550 Hardware Configuration]-------------------------------------------
#CONFIG
CONFIG PLLDIV = 5 ...
Thank You, I will try your code. I went another direction but I will order another display just to try this. Thanks again!
PCF8574AT is the number on my IC.
This is the init command from my working Arduino sketch "LiquidCrystal_I2C lcd(0x3F, 2, 1, 0, 4, 5, 6, 7, 3, POSITIVE)" all three jumpers are open A0:2.
Thanks!
I see on the data sheet for the PCF8574 you are right I used the Arduino i2c address finder to get the address. I have tried it using the 4E address and get nothing however with the 7E I do get some...
Richard thank you for your help.
I have read most of the threads but will read them again. I will find and download both version of the include. On Arduino this is the Initialization for my...
Sorry, I should have said 16F628A. I did set my pins as digital? I want to display data from my program but that seems far away at this point?? I cut the program down to the below lines and I get a...
I did delete these two lines
ARRAYWRITE LCD_Buff,[" LCD PCF8574"] : LCD_WriteBuff
ARRAYWRITE LCD_Buff,[$FE,$C0,"Count = ",DEC LoopCount," "] : LCD_WriteBuff
and Change this line
...
I am trying to make this code work with a 16F629A and all I get is a blinking back light with the modified code below.I am probably missing something simple?
Thanks,
; Filename :...